Skip to content
Log in

Print station tickets over the network

On this page

A fulfillment station can sit well away from the register that takes the order, in which case the printer the docket needs is not plugged into the device that sends it. Use the StoreConnect Android app on a tablet to reach printers over Wi-Fi, LAN, or Bluetooth instead of USB.

This matters for stations in particular, because one tablet can hold a print connection to a separate printer for each station, all on the same network. One device set up this way serves the whole venue: a printer at the kitchen, another at the bar, another at a packing bench, each receiving only its own station’s dockets.

What each build of POS supports

Build Printer connections Notes
Browser POS on desktop or laptop USB only, through the WebUSB API Detects a disconnected printer and offers a Reconnect button
StoreConnect Android app on a tablet Wi-Fi, LAN, Bluetooth, and USB Discovers printers through its own printer picker
Browser POS on an iPad Not supported for printers iOS browsers do not expose WebUSB

The Android app is the only way to print to a network printer from a tablet. Everything else about stations, including routing, printer assignments, auto-print, and print tracking, works identically in both builds.

Before you start

  • The StoreConnect Android app is installed on the tablet and signed in to the register
  • The tablet and every printer are on the same Wi-Fi network or subnet
  • The app has the Nearby devices permission (Location on Android 10 and 11), and Location is turned on in the tablet’s settings. Epson printer discovery does not run with Location turned off
  • Each printer is powered on with paper loaded, and network printers have an IP address assigned
  • A station ticket template is selected on the device, as covered in Set up station tickets on a register

Step 1: Discover the printers

  1. On the tablet, select Settings in the sidebar.
  2. Select Set up hardware, then Receipt printer.
  3. The Select a Printer picker opens and scans the network. Discovered printers are listed with the manufacturer, the model, and the connection, for example LAN · 192.168.1.50.
  4. Use the search box to narrow the list by model, host, or connection type when a venue has many printers.
  5. Select Refresh to scan again after plugging in or powering up a printer.
  6. Select the printer you want to add.

If nothing is found, the picker says so and names two things to check: that the tablet is on the same Wi-Fi as the printer, and that the app has the Nearby devices permission (Location on Android 10 and 11) with Location turned on.

Step 2: Name and test the printer

Selecting a printer opens the Printer setup complete screen. Finish the setup there before moving on.

  1. Set a Device name that matches where the printer physically is, for example Kitchen counter or Bar front. This is the name that appears in the Assign printers picker, so make it recognizable to whoever is assigning printers to stations.
  2. Check the Manufacturer, Model, and Serial number rows. Each reads Not detected when the value did not resolve.
  3. Confirm the Printer profile matches the hardware. StoreConnect recognizes the Star mPOP and the Epson TM-T88IV automatically, and shows a banner asking you to set the profile by hand for anything it does not recognize.
  4. Select Run test print to send a sample to that printer, then select Done.

Repeat for each printer the tablet needs to reach. To come back to a printer later, go to Settings, Manage hardware, then the printer.

:::note An Epson printer that reports no serial of its own is given its MAC address as the serial. Star printers, and printers found through mDNS (Bonjour) discovery, get no serial. Two identical network printers can still be assigned to different stations, because the app sends each print to the printer’s host or target, not to a serial. The refusal to add a second identical printer with no serial applies only to USB printers. :::

Step 3: Assign printers to stations

With more than one receipt printer set up on the tablet, assign each station the printer beside it. The procedure is the same as on browser POS and is covered in Set up station tickets on a register.

Printer assignments are stored on the tablet, not on the station record, so each device chooses its own printers even when two devices cover the same station.

Supported printers and protocols

The app prints raw commands to the printer in its own language, chosen from the printer profile.

Printer profile language Printers How the printer is addressed
star-prnt Star Micronics, including the mPOP The discovered host or address, with the connection type, defaulting to LAN
esc-pos Epson and compatible A target string prefixed by the connection: TCP: for LAN and Wi-Fi, BT: for Bluetooth and Bluetooth LE, USB: for USB

For an ESC/POS printer, the app uses the target stored when the printer was discovered. A printer paired before targets were stored has none, so the app builds one from the stored host and connection type, and the printer keeps working without staff re-pairing it. Star printers are addressed by host and do not use a target. A bare IPv4 address with no recorded connection type is treated as a network printer, since an IP address can only be reached over TCP. A hostname with no connection type cannot be resolved this way, and the app asks you to run discovery again.

Two errors tell you which case you have hit:

  • Printer has no reachable address; re-run printer discovery. The stored printer has no host at all. Remove it and discover it again.
  • Can't determine how this printer is connected; re-run printer discovery, or reconnect it over LAN, USB, or Bluetooth. The printer has a host but no usable connection type. Discover it again so the connection is recorded.

Differences from browser POS

Two behaviors are specific to the browser build and are absent in the Android app, because the app has no way to poll a network printer’s connectivity.

  • No offline printer banner. Browser POS warns on the station details screen, the ticket workspace, and the printer settings page when a station’s assigned printer is unreachable. The app does not.
  • No Reconnect button. In the browser, a Star mPOP that reports no USB serial needs the Reconnect button after being unplugged. In the app there is nothing to re-approve.

In the app, a print that cannot reach its printer fails only when the print is attempted, and the attempt runs for up to two minutes before it reports a timeout. The ticket is not marked as printed and stays in the queue.

:::warning A held ticket prints by itself once the printer is back, as long as the ticket is still open, but only when the POS next runs the print cycle. A network printer sends no reconnect signal, so the cycle runs when the POS reloads or when a ticket changes or syncs on the device, such as a new order arriving. To print the held ticket straight away, reload the POS. Do not reprint it by hand while it waits: a manual reprint does not count as the automatic print, so the station gets a second docket when the cycle runs. Because a network printer cannot be polled, nothing on the screen announces that a station has stopped printing, so keep the unprinted-ticket report described in Track station ticket printing under active watch during service. :::

:::note Document printers are the exception to all of this. They are managed through the tablet’s own Android print settings, not through StoreConnect, and the app says so if you try to add one. :::

Once discovery and printer assignment are done, a test print reaches the correct physical printer from the tablet, and a real order routed to a station produces its docket at that station’s printer with no cable between the tablet and the printer.

Was this article helpful?

Was this article helpful?